DTP DVI 230 Tx/Rx
 NOTE     This product consists of a transmitter (DTP DVI 230 Tx) and a receiver (DTP DVI 230 Rx), sold separately, with a twisted pair cable linking the transmitter and receiver.
 NOTE     *Appropriate DVI-D to HDMI cables or adapters are required for DVI signal input/output.
   Maximum data rate  6.75 Gbps (2.25 Gbps per color)
   Maximum pixel clock  165 MHz
   Resolution range  Up to 1920x1200 or 1080p @ 60 Hz; 8, 10, or 12 bit color depth
   Formats  RGB and YCbCr digital video
   Standards  DVI 1.0, HDMI, HDCP 1.1, CEA-861E
Video input — transmitter
   Number/signal type  1 single link DVI-D (or HDMI*) input
1 single link DVI-D (or HDMI*) local loop-through
   Connectors  2 female DVI-I
Interconnection between transmitter and receiver
   Connectors  1 female RJ-45 per unit
   Termination standard  TIA/EIA T568B
   Signal transmission distance  Up to 230' (70 m) using CAT 5e/6/6a/7 cable or XTP DTP 24 TP cable
      Cable recommendations  400 MHz bandwidth, STP (shielded twisted pair)
      Cable requirements  Solid conductor, 24 AWG or better
       NOTE     Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
Video output — receiver
   Number/signal type  1 single link DVI-D (or HDMI*)
   Connectors  1 female DVI-I
   Gain  Unbalanced output: 0 dB; balanced output +6 dB
   Frequency response  20 Hz to 20 kHz, ±0.5 dB
   THD + Noise  0.03% @ 20 Hz to 20 kHz at maximum output
   S/N  >90 dB, at maximum output (15 dBu), balanced (unweighted)
   Stereo channel separation  >80 dB @ 1 kHz to 20 kHz
Audio input
   Number/signal type  1 PC level stereo, unbalanced
   Connectors  (1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground)
   Impedance  >10k ohms, DC coupled
   Nominal level  -10 dBV (316 mVrms)
   Maximum level  +7 dBV (unbalanced)
    NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio output
   Number/signal type  1 stereo (2 channel), balanced/unbalanced
   Connectors  (1) 3.5 mm captive screw connector, 5 pole
   Impedance  50 ohms unbalanced, 100 ohms balanced
   Gain error  ±0.1 dB channel to channel
   Maximum level (600 ohm)  >+11 dBu, balanced
Control/remote — external device (pass-through, unidirectional or bidirectional)
   Serial control port input/output   
      Transmitter  RS-232 via (1) 3.5 mm, 5 pole captive screw connector for RS-232 control (±5 V) (connector is shared with IR control port)
      Receiver  1 set of proprietary signals on a female RJ-45 jack
   Serial control port output/input   
      Transmitter  1 set of proprietary signals on a female RJ-45 jack
      Receiver  RS-232 via a 3.5 mm, 3 pole captive screw connector
   Baud rates  Up to 115200 baud
   Protocol  Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none
   Serial control pin configuration  1 = Tx, 2 = Rx, 3 = GND
   IR control port  (1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz
   IR control pin configuration  3 = GND, 4 = IR Tx, 5 = IR Rx
   Power supply  External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1 A, 12 watts
   Power consumption  11.0 watts, 12 VDC, total, for both transmitter and receiver
    NOTE     Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable.
   Temperature/humidity  Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
   Cooling  Convection, no vents
      Rack mount  Yes, with optional 1U high rack shelf
      Furniture mount  Yes, with optional under-desk mounting kit
   Enclosure type  Metal
   Enclosure dimensions   
      Transmitter  1.0" H x 4.3" W x 3.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 7.6 cm D)
(Depth excludes connectors.)
      Receiver  1.0" H x 4.3" W x 6.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 15.2 cm D)
(Depth excludes connectors.)
   Product weight   
      Transmitter  0.5 lbs (0.3 kg)
      Receiver  1.0 lb (0.5 kg)
   Shipping weight  3 lbs (2 kg)
   Vibration  ISTA 1A in carton (International Safe Transit Association)
   Regulatory compliance   
      Safety  CE, c-UL, UL
UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply; meets UL 60065 and IEC 60065 for A/V equipment saftey.
      EMI/EMC  CE**, C-tick, FCC Class A**, ICES, VCCI
    NOTE     **CE and FCC testing is conducted with STP (shielded twisted pair) I/O cable.
   Warranty  3 years parts and labor
    NOTE     All nominal levels are at ±10%.
    NOTE     Specifications are subject to change without notice.
Quý khách có thể gửi ý kiến mà không cần đăng nhập tài khoản khách hàng.
Họ tên
Đánh giá
Ý kiến
Sản phẩm cùng nhóm
Liên hệ 090.536.6656

The Extron DTP DVI 230 Tx is a transmitter for transmission of DVI-D video, audio, and bidirectional RS-232 and IR signals over a single CATx cable to an Extron DTP 230 receiver. It provides an economical and effective means for extending single link DVI-D or HDMI signals. In addition, the DTP DVI 230 accepts analog stereo audio signals and digitizes them for simultaneous transmission over the same twisted pair cable. It is capable of sending 1920x1200, 1080p/60 Deep Color, and 2K signals up to 230 feet (70 meters). The transmitter is equipped with a buffered DVI loop-through output to support a local computer monitor. The compact enclosure sizes and remote power capability make the DTP DVI 230 ideal for extending DVI-D, audio, and bidirectional control in space-challenged environments.

  • Bảo Hành: 3 tháng chính hãng