MPS 602

MPS 602
 
Video — VGA
   Gain  Unity
   Bandwidth  350 MHz (-3 dB)
   Crosstalk  -50 dB @ 10 MHz, -30 dB @ 100 MHz
   Switching speed  <5 ms (max.)
 
Video — HDMI and DTP
   Maximum data rate  6.75 Gbps (2.25 Gbps per color)
   Maximum pixel clock  165 MHz
   Resolution  1920x1200 @ 60 Hz or 1080p @ 60 Hz, 12 bit color, and 2K
   Formats  RGB and YCbCr digital video
   Standards  DVI 1.0, HDMI, HDCP 1.1, CEA-861E
 
Video input
 
DTP signal
   Number/signal type   
      VGA inputs  2 VGA-QXGA RGBHV, RGBS
      HDMI inputs  3 HDMI (or single link DVI-D), with appropriate DVI-HDMI adapters)
      DTP input  1 DTP 230 input

 

   Connectors   
      VGA inputs  2 female 15-pin HD
      HDMI inputs  3 female HDMI type A
      DTP input  1 RJ-45 jack
   Nominal level   
      VGA inputs  0.7 Vp-p for RGB
   Minimum/maximum levels   
      VGA inputs  Analog 0.3 V to 1.5 Vp-p with no offset
      Impedance  75 ohms
   Horizontal frequency  15 kHz to 145 kHz
   Vertical frequency  30 Hz to 170 Hz
   Return loss   
      VGA inputs  <-40 dB @ 5 MHz
 
Video output
   Number/signal type   
      Local VGA output  1 VGA-QXGA RGBHV, RGBS
      HDMI outputs  1 HDMI (or single link DVI-D)
      DTP output  1 DTP 230 output
      DTP signal   
         Transmission distance  up to 230' (70 m) using CAT 5e/6/6a/7 cable or XTP DTP 24 TP cable
         Cable requirements  Solid conductor, 24 AWG or better
         Cable recommendations  400 MHz bandwidth, STP (shielded twisted pair)
       NOTE     Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
   Connectors   
      Local VGA output  1 female 15-pin HD
      HDMI outputs  1 female HDMI type A
      DTP output  1 RJ-45 jack
    NOTE     Outputs are selectable from either the HDMI output or DTP output. The switcher does not output to both connectors simultaneously. Analog RGB inputs are digitized for output from either the HDMI or DTP output.
   Nominal level   
      VGA outputs  0.7 Vp-p for RGB
   Minimum/maximum levels   
      VGA outputs  Analog, 0.3 V to 1.5 Vp-p
   Impedance  75 ohms
   Return loss (VGA output)  <-40 dB @ 5 MHz
   DC offset (max. allowable, VGA output)  ±5 mV with input at 0 offset
 
Sync — VGA Inputs Only
   Input type  RGBHV, RGBS
   Local VGA output  RGBHV, RGBS
   Input level  1.9 V to 5.0 Vp-p
   Output level  TTL: 5.0 Vp-p (unterminated) for RGBHV, RGBS
   Input impedance  510 ohms
   Output impedance  75 ohms
   Max. input voltage  5.0 Vp-p
   Max. propagation delay  30 ns
   Max. rise/fall time  4.2 ns
   Polarity  Positive or negative (follows input)
 
Audio — individual audio groups (VGA, HDMI)
   Gain  Unbalanced output: 0 dB; balanced output: +6 dB
   Frequency response  20 Hz to 20 kHz, ±0.5 dB
   THD + Noise   
      MPS 602  0.01% @ 1 kHz at nominal level
      MPS 602 SA/MA  0.1% @ 1 kHz 3 dB below clipping
   S/N   
      MPS 602  >90 dB at maximum output (unweighted)
      MPS 602 SA/MA  >90 dB 20 Hz to 20 kHz, unweighted
   Crosstalk  <-72 dB @ 1 kHz or below, <-45 dB @ 20 kHz
   Stereo channel separation  >80 dB @ 20 Hz to 20 kHz
   CMRR  >75 dB @ 20 Hz to 20 kHz
 
Audio input — (VGA, and HDMI video)
   Number/signal type   
      VGA inputs  2 stereo, unbalanced/balanced
      HDMI inputs  3 stereo, unbalanced
      DTP input  1 stereo, unbalanced/balanced analog,
1 embedded digital audio from DTP
   Connectors   
      VGA inputs  (2) 3.5 mm, 5-pole captive screw connectors
      HDMI inputs  (3) 3.5 mm 5-pole captive screw connectors
(3) female HDMI type A
      DTP input  1 female RJ-45 connector
   Input impedance  >10k ohms unbalanced, 20 k ohms balanced
   Nominal level  +4 dBu, -10 dBV configurable
   Maximum level  +21 dBu, balanced, +15 dBu unbalanced
   CMRR  >60 dB typical @ 1 kHz
   Input gain adjustment  -18 dB to +24 dB, adjustable per input
    NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
 
Audio output
   Number/signal type  (2) stereo, balanced/unbalanced (fixed and variable outputs)
(1) DTP 230 analog audio
(1) embedded digital audio on HDMI
   Connector  (2) 3.5 mm captive screw connector, 5-pole
(1) RJ-45
(1) female HDMI type A
   Impedance  50 ohms unbalanced, 100 ohms balanced
   Gain error  ±0.5 dB channel to channel
   Nominal level when the main volume is set to default  -2 dBu (632 mVrms) balanced output
   Maximum level (Hi-Z)  >16.5 dBu balanced, >8.2 dBV unbalanced at 1% THD+N
   Talk-over (ducking) response time (typical)
      Attack time  Instant
      Release delay  5 seconds
      Release time  1 second
      Ducking level  0 dB to 30 dB, adjustable; default = +6 dB
 
Audio output — power amplifier
   Number/signal type   
      MPS 602 SA  1 stereo (default) or 2 mono, 2 channels total
      MPS 602 MA  1 mono, 70V line
   Connector   
      MPS 602 SA  (1) 5 mm screw lock captive screw connector, 4-pole
      MPS 602 MA  (1) 5 mm screw lock captive screw connector, 2-pole
   Load impedance   
      MPS 602 SA  4 ohms minimum
      MPS 602 MA  50 ohms minimum
   Output power   
      MPS 602 SA  25 watts per channel, 8 ohms, 1 kHz, 0.1% THD
50 watts per channel, 4 ohms, 1 kHz, 0.1% THD
      MPS 602 MA  100 watts per channel, 4 ohms, 1 kHz, 0.1% THD
   THD + Noise  0.1% @ 1 kHz, 3 dB below clipping
   Amplifier type  Class D
 
Mic/line input
   Number/signal type  1 mono balanced/unbalanced
   Connector  (1) 3.5 mm captive screw connector
   Impedance  10k ohms unbalanced, 20k ohms balanced
   Nominal level  -60 dBV (1 mV), +4 dBu, -10 dBV, adjustable
   Equivalent input noise  <-117 dBV (1.4 uVrms) when gain is set to 40 dB
   Maximum level  +12 dBV (2 Vrms) when gain is set to 0 dB
   CMRR  >60 dB typical @ 1 kHz
   Input gain adjustment  -18 dB to +60 dB, 1 dB steps, adjustable per input
   Microphone volume range  -66 dB to +12 dB
   Microphone DC power  +48 VDC phantom power, can be turned on or off
    NOTE     Mic/Line audio is not embedded on DTP analog audio output or digital embedded audio.
 
Control/remote — switcher
   Serial control port  1 RS-232, 3.5 mm captive screw connector, 3-pole, rear panel
   Baud rate and protocol  9600 baud, 8 data bits, 1 stop bit, no parity
   Serial control pin configuration  2 = Tx, 3 = Rx, 5 = GND
   IR controller module  IR 102 remote control kit, optional (70-224-01) 30' maximum, 40 degrees off axis
   USB control ports  1 front panel female mini USB B
   USB standards  USB 2.0, high speed
   Ethernet control port  1 female RJ-45 connector
   Ethernet data rate  10/100 Base-T, half/full duplex with auto-detect
   Ethernet protocol  ARP, ICMP (ping), IP, TCP, DHCP, HTTP, Telnet
   Program control  Microsoft Internet Explorer®
Extron Simple Instruction Set (SIS)
Telnet
 
General
   Power supply  Internal
Input: 100-240 VAC, 50-60 Hz, 20 watts
   Remote power capability  Supports up to two endpoints (one DTP Tx, one DTP Rx)
   Temperature/humidity  Storage -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
   Cooling  Convection, no vents
   Power consumption  22 watts
   Thermal dissipation   
      MPS 602  Full load, 22 watt (69 BTU/hr)
      MPS 602 SA  Full load, amp at 1/8 power:
44 watt (102 BTU/hr)
      MPS 602 MA  Full power, amp at 1/8 power:
44 watt (102 BTU/hr)
   Mounting   
      Rack mount  Yes, with included brackets
   Enclosure type  Metal
   Enclosure dimensions  1.75" H x 17.4" W x 8.5" D (1U high, full rack wide)
4.4 cm H x 43.2 cm W x 21.6 cm D
(Depth excludes connectors and knobs. Width excludes rack ears.)
   Product weight  7.0 lbs (3.2 kg)
   Shipping weight  10 lbs (5 kg)
   Vibration  ISTA 1A in carton (International Safe Transit Association)
   Regulatory compliance   
      Safety  CE, c-UL, UL
      EMI/EMC  CE, C-tick, ICES, FCC Class A, VCCI
      Environmental  Complies with the appropriate requirements of RoHS, WEEE
   Warranty  3 years parts and labor
    NOTE     All nominal levels are at ±10%.
    NOTE     Specifications are subject to change without notice.
Quý khách có thể gửi ý kiến mà không cần đăng nhập tài khoản khách hàng.
Họ tên
Đánh giá
Ý kiến
Sản phẩm cùng nhóm
Liên hệ 090.536.6656
HDMI DA SERIES

The Extron HDMI DA Series of distribution amplifiers reliably distributes one HDMI source signal to two, four, or six displays. The HDMI DA Series supports HDMI specification features including data rates up to 6.75 Gbps, 12-bit Deep Color, 3D, Lip Sync, and HD lossless audio formats. The HDCP-compliant distribution amplifiers support HDTV 1080p/60, 2K, and PC resolutions up to 1920x1200. The HDMI DA Series features two Extron-exclusive technologies: EDID Minder, which maintains continuous EDID communication between connected devices, and Key Minder, which continuously authenticates HDCP encryption between all devices, ensuring the simultaneous distribution of source content to all displays. The HDMI DA Series is ideal for applications that require the distribution of an HDMI source signal to multiple displays.
Model:
HDMI DA2 Two Output HDMI
HDMI DA4 Four Output HDMI
HDMI DA6 Six Output HDMI

  • Bảo Hành: 3 tháng chính hãng